Hammer-type material level gauge is installed on the top of the silo. The detection process of material level gauge sensor is controlled by the signal from the control display. The mechanical transmission part of the heavy hammer material level meter is composed of reversible motor, screw, gear shaft, winding barrel, sensitive lever, etc.

When the material level meter sensor receives the detection command: the motor is rotating to drive the gear shaft and the winding barrel to rotate, so that below the wire rope, the heavy hammer is driven down from the top of the warehouse. When heavy hammer fell to the material plane was a face lift and weightlessness, wire rope is flabby, sensitive lever action that micro switch contact, control monitor motor reversal command from the signal immediately, a heavy hammer rise in return, until a winding drum hit to switch, motor stalling, weight back to the original warehouse top location, complete a detection process.

In this process, the control display calculates the distance between the hammer from the bottom of the silo to the material level surface by detecting the revolution of the winding barrel, carries on the digital display on the panel, and outputs the 4-20mA current on the back panel terminal.

Product features:

1. Different structure and transmission mode;

2, steel wire rope durable, than other domestic brands of steel wire rope life doubled;

3, Anti-jamming, anti-death, intelligent protection circuit, intelligent alarm;

4, automatic and manual can be switched at will;

5, reliable operation, free detection, small maintenance, wide application;

6, the specific environment has little impact on the equipment, can adapt to the harsh field environment.

Technical parameters:

Measuring range: 0-10/20/40 m

Measuring accuracy: ±1%

Repeatability: ±1%

Resolution: ±2cm

Detection speed: 0.14m/s

Measuring tape: stainless steel wire rope

Heavy hammer weight: 1.5kg (0-20m),2Kg(0-40m)

Power consumption: 90 w

Ambient temperature: -10℃ -+ 60℃

Weight: 10 m 50Kg 20 m 60Kg 40 m 75Kg

French standard: JB81-59 outside diameter 195mm aperture 18mm hole center distance 160mm(PN1.0,DN80)

Outlet port: M20×1.5

Control display:

Power supply voltage: 220VAC±10% 50/60Hz

Power consumption: 15W at rest, 105W at motion

Ambient temperature: -30℃ -+ 60℃

Digital display: 4 LED display material surface position

Current output: 4-20mA DC

Timed running time: 30 minutes

Weight: 2 kg

Power principle:

It is composed of hammer, cable, pulley, position sensor and control circuit. When measuring, the hammer drops and the cable rotates with the artery pulley. The position sensor and control circuit calculate the number of turns of the pulley and calculate the distance of the drop when the hammer touches the material.

Measurement Advantages:

The low temperature resistance of the electronic warehouse can reach -40℃. The optical sensor isolation seal fundamentally avoids the pollution of dust, etc. The excellent driving motor and heavy duty steel cable can provide strong tensile resistance. Patented winding device to ensure that there will be no disorderly wire, wire jump problem.

The weight level meter is especially suitable for the material level measurement in the heavy dust environment. It can avoid the ultrasonic level meter can not penetrate the heavy dust and avoid the important defect of dust accumulation at the root of radar level meter antenna. It is the choice in the heavy dust measurement environment. Widely used in PVC powder silo, cement silo, power plant gray silo and other harsh environment, and achieved success, users praise.

Application Guide:

Hammer type material level meter can measure feed, chemicals, plastic particles, cement, stone, PVC powder, aggregate, liquid, coal, limestone, grinding plastic, sand, powder, grain, oil, etc. At the same time, it is suitable for power plant ash warehouse, coal bunker, slag bin, mud pool, etc.

Specific advantages:

1. Mechanical measurement, simple and reliable, strong anti-dust interference ability;

2. Measuring range up to 45.7 meters;

3. Multiple dustproof design (dustproof brush, air inlet hole, isolation of measuring room);

4. Not affected by the humidity and viscosity of the medium;

5. Not affected by the dielectric constant, electrical conductivity and thermal conductivity of the medium;

6. Can be used to measure mud, pulp, asphalt (high temperature) and other special liquids.

Note:

1. The main application object is the solid with small particle size, and the large-size ore is not applicable;

2. The installation position is generally selected at about 1/6 bin diameter;

3. The installation of heavy hammer type material level timing should try to avoid the feeding port, obstacles, stirring paddle and other interference factors.